Wifi6& BLE5.4 dual mode communication module IOT module factory price wifi module in iotun Technology Co., Ltd

Product Introduction

HY-330101 module is based on TI (Texas Instruments) CC3301 as the core design of a WIFI+ Bluetooth 2-in-1 wireless module. Wifi supports IEEE 802.11b /g/n/ax MAC, baseband and RF transceivers, 2.4GHz, 20MHz, single-space streaming, hardware-based encryption and decryption, supports WPA2 and WPA3, supports 4-bit SDIO host interface, and application throughput up to 50Mbps. Bluetooth supports low power Bluetooth® 5.4, LE coded PHY (long distance), LE 2M PHY (high speed) and broadcast extension, and Host Controller interface (HCI) transmission using UART interface. The module is packaged with a 44PIN stamp hole, the size is 12*12*2.5mm (including shielding cover).

Product Features

Wi-Fi 6 (802.11ax);

2.4GHz Wi-Fi 6 and Bluetooth Low Energy 5.4 matching ics;

A companion IC for any processor or MCU host capable of running the TCP/IP stack;

Integrated 2.4GHz PA for complete wireless solutions with output power up to +20dBm;

Operating temperature: -40°C to +105°C;

Application throughput up to 50Mbps;

Enhanced security

- Security host interface

- Firmware authentication

- Anti-rollback protection;

Multi-role support (for example, concurrent STAs and aps) to connect Wi-Fi devices on different RF channels (Wi-Fi networks);

Power management

- VIO: 1.8V

- VBAT: 3.0V to 3.6V

Product parameters

Model number	HY-330101
Chip	CC3301
Authentication	-
Chipset	CC3301
Antenna type	Custom
RAM	no
Flash	no
Support Protocol	wifi6
Supply Power Voltage	1.8---3.V
Frequency	2.4GHz/5GHz
Maximum Transmitting power	17dbm
Receiving sensitivity	-95dbm @1Mbps DSSS
RX power	62mA
TX power	525mA
GPIO	无GPIO
Operating temperature	-40℃~+105℃
Communication distance
Size	12122.7mm
Other Protocol	BLE 5.4
Role type	WIFI&BLE module

Main Chipset	TI3301
Standard	IEEE 802.11b/g/n/ax, Bluetooth low energy 5.3
Bus Interface	SDIO/ UART
Frequency Range	2.412GHz~2.472GHz
Transmit Output Power	WLAN Performance: 2.4-GHz Transmitter Power @1 Mbps DSSS: 20.5 dBm @6 Mbps OFDM: 20.5 dBm @54 Mbps OFDM: 17 dBm @HT MCS0 MM: 20 dBm @HT MCS7 MM: 16.5 dBm @HE MCS0: 20 dBm @HE MCS7: 16 dBm BLE Performance: 20 dBm
Receive Sensitivity	WLAN Performance: 2.4-GHz Receiver Characteristics (Sensitivity: 8% PER for 11b rates, 10% PER for 11g/n/ax rates) @1 Mbps DSSS -98 dBm @2 Mbps DSSS -95 dBm @11 Mbps CCK -90 dBm @6 Mbps OFDM -93.5 dBm @54 Mbps OFDM -75.8 dBm @HT MCS0 MM 4K -93 dBm @HT MCS7 MM 4K -73.6 dBm @HE MCS0 4K -91.3 dBm @HE MCS0 4K ER upper 106 -93.3 dBm @HE MCS7 4K -72.4 dBm BLE Performance: BLE 1Mbps (LE 1M) Receiver Characteristics Receiver sensitivity: -99.4dBm (37-byte packets) Receiver sensitivity: -98.5dBm (255-byte packets)
Operating temperature	-40°C to +105°C
Operating Voltage	V_MAIN, V_IO, V_PP: 1.8 V (1.62V to 1.98V) V_PA : 3.3V (3.0 V to 3.6V)

PIN	Name	PAD type	Description
1	GND	-	Ground
2	RF_BG	I/O	Bluetooth Low Energy and WLAN 2.4-GHz RF port
3	GND	-	Ground
9	VBAT	P	Internal power supply input
10	XTAL_IN	NA	XTAL_P
11	XTAL_OUT	NA	XTAL_N
12	NRESET	I	Reset line for enabling or disabling device (active low)
13	HOST_IRQ_WL	I/O	Interrupt request to host for WLAN
14	SDIO_D2	I/O	SDIO data pin
15	SDIO_D3	I/O	SDIO data pin
16	SDIO_CMD	I/O	SDIO card command pin
17	SDIO_CLK	O	SDIO clock pin
18	SDIO_D0	I/O	SDIO data pin
19	SDIO_D1	I/O	SDIO data pin
20	GND	-	Ground
22	VDDIO	P	I/O power supply input
24	SLOW_CLK_IN	I	32.768-kHz RTC clock input
31	GND	-	Ground
33	GND	-	Ground
36	GND	-	Ground
41	UART_RTS	I/O	Device RTS signal - flow control for BLE HCI
42	UART_TX	I/O	UART TX for BLE HCI
43	UART_RX	I/O	UART RX for BLE HCI
44	UART_CTS	I/O	Device CTS signal - flow control for BLE HCI
4,5,6,7,8,21,23,30,25, 26,27,28,29,32,34,3 41,,42,43,44	NA	NA	NA

Order Method

Data download

title	version	release date	download
HY-330101 WLAN MODULE SEPC.pdf		2023.12.15

Application Cases

Name:
Phone:
Message content: